KYORITSU 6310-01 Power Quality Analyzer with Load Current Clamp

Kyoritsu 6310 01 Power Quality Analyzer with Load current clamp sensor Model 8125 500A times 3

•         Can measure Flicker in accordance to IEC 61000-4-15 and EN50160 standards. Using our Flicker sensor, available as optional accessory, Pst value (short term severity in 10 minutes value) and the Plt value (long term severity in 2 hours value) can be measured.

•         12 kinds of Power Measurements for Power Control and Applicable to Power Quality Control including Harmonics Analysis.

•         One click easy-to-use operation helps complicated setting and processing of large data through the setting / analyzing software provided as accessory.

•         Direct communication with PC via USB cable

•         Built-in Input / Output Function of external signal enables the signal transmission to alarms.

•         2-way power supply by AC and Battery, and Nickel hydrogen battery usable with rechargeable function.

•         Pull / Insert of CF card possible whenever on recording under the function of memory backup device.

•         Can monitor insulation at leakage current by using optional leak clamp sensors.

•         Built-in Print Screen Function enables to record display screen

•         (Records 512 screens by using CF card: 1 screen 40KB).

•         Can display Waveform and Vector, and can confirm the wiring connection, too.

•         Complies fully with International Safety Standards IEC 61010-1 CAT.III 600V.

Wiring connections: 1P 2W, 1P 3W, 3P 3W, 3P 4W

Measurements and parameters Voltage, Current, Frequency, Active power, Reactive power, Apparent power, Active energy, Reactive energy, Apparent energy, Power factor (cos θ), Neutral current, Demand, Harmonics, Quality (Swell/Dip/Instantaneous Stop, Transients/Over Voltage, Inrush Current, Unbalance Rate, IEC Flicker [Pst(1 min)*, Pst, Plt]), Phase Advance Condenser (*Pst can be shown in details for 1 minute intervals.)

Other functions Digital output function, External communication function, Scaling function

Voltage : Ranges [RMS]: 150 / 300 / 600 /1000V (CF: 2.5 or less, 100% or less of each range) Allowable input : 10~110% of each range (1000V range : 20%~) Display ranges: 5~120% of each range Accuracy : ±0.3%rdg±0.2%f.s. (sine wave, 45~65Hz)

•         8128 ( 50A type ) : 1 / 5 / 10 / 20 / 50A

•         8127 ( 100A type ) : 10 / 20 / 50 / 100A

•         8126 ( 200A type ) : 20 / 50 / 100 / 200A

•         8125 ( 500A type ) : 50 / 100 / 200 / 500A

•         8124 ( 1000A type ) : 100 / 200 / 500 / 1000A

•         8129 ( 3000A type ) : 300 / 1000 / 3000A

•         (CF: 3.0 or less. 90% or less of each range)

Allowable input - 10~110% of each range Display ranges - 1~120% of each range Accuracy ±0.3%rdg±0.2%f.s. + Accuracy of Clamp sensor (sine wave, 45~65Hz)

Activa power accuracy: ±0.3%rdg±0.2%f.s. + Accuracy of Clamp sensor (Power factor 1, Sine wave, 45~65Hz)

Influence of power factor: ±1.0%rdg (reading at power factor 0.5 against power factor 1)

Frequency meter range: 40~70Hz Display: 320×240 (RGB) Pixel, 3.5-inch color STN display

Temperature & humidity range: 23ºC±5ºC, Relative humidity 85% or less (no condensation)

Storage Temperature & humidity range: -20ºC±60ºC, Relative humidity 85% or less(no condensation)

Operating Temperature & humidity range: 0ºC±40ºC, Relative humidity 85% or less(no condensation)

Power supply: AC 100V ~ 240V±10% (45~65Hz) Alkaline size AA battery LR6 (9V 1.5V × 6) or Ni-MH (HR15-51)