GW INSTEK GSP-9300 SPECTRUM ANALYZERS
Gambar Produk
GW INSTEK GSP-9300 SPECTRUM ANALYZERS
Update Terakhir
23-02-2016
Dilihat Sebanyak
154 kali
Lokasi
Jawa Barat - Bekasi
Harga
Kontak Kami
Bagikan
+ Penawaran
Spesifikasi GW INSTEK GSP-9300 SPECTRUM ANALYZERS
Features
Frequency
Frequency
Range
9 kHz to 3.0 GHz
Resolution
1 Hz
Frequency Reference
Accuracy
±[(period since last adjustment X aging rate) + stability over temperature + supply voltage stability
Aging Rate
±2 ppm max.
1 year after last adjustment
Frequency Stability over Temperature
±0.025 ppm
0 to 50 °C
Supply Voltage Stability
±0.02 ppm
Frequency Readout Accuracy
Start, Stop, Center, Marker
±(marker frequency indication X frequency reference accuracy + 10% x RBW + frequency resolution*1)
Sweep points
601
Span >= 100 Hz
6 to 601
Span = 0 Hz
Marker Frequency Counter
Resolution
1 Hz, 10 Hz, 100 Hz, 1 kHz
Accuracy
±(marker frequency indication X frequency reference accuracy + counter resolution)
Frequency Span
Range
0 Hz (zero span), 100 Hz to 3 GHz
Resolution
1 Hz
Accuracy
± frequency resolution*1
Phase Noise
Offset from Carrier
Fc =1 GHz; RBW = 1 kHz, VBW = 10 Hz;Average ≥ 40
10 kHz
<-88 dBc/Hz
Typical2
100 kHz
<-95 dBc/Hz
Typical
1 MHz
<-113 dBc/Hz
Typical
Resolution Bandwidth (RBW) Filter
Filter Bandwidth
1 Hz to 1 MHz in 1-3-10 sequence
-3dB bandwidth
200 Hz, 9 kHz, 120 kHz, 1 MHz
-6dB bandwidth
Accuracy
± 8%, RBW = 1 MHz
Nominal3
± 5%, RBW < 1 MHz
Nominal
Shape Factor
< 4.5:1
Normal Bandwidth ratio: -60dB:-3dB
Video Bandwidth (VBW) Filter
Filter Bandwidth
1 Hz to 1 MHz in 1-3-10 sequence
-3dB bandwidth
[1] Frequency Resolution = Span/(Sweep points - 1)
[2] Typical specifications in this datasheet mean that the performance can be exhibited in 80% of the units with a 95% confidence level over the temperature range 20 to 30 °C. They are not covered by the product warranty.
[3] Nominal values indicate expected performance. They are not covered by the product warranty.
Amplitude
Amplitude Range
Measurement Range
100 kHz to 1 MHz
Displayed Average Noise Level (DANL) to 18 dBm
1 MHz to 10 MHz
DANL to 21 dBm
10 MHz to 3 GHz
DANL to 30 dBm
Attenuator
Input Attenuator Range
0 to 50 dB, in 1 dB step
Auto or manual setup
Maximum Safe Input Level
Average Total Power
<= 33 dBm
Input attenuator
≥10 dB
DC Voltage
± 50 V
1 dB Gain Compression
Total Power at 1st Mixer
> 0 dBm
Typical;Fc ≥50 MHz; preamp. off
Total Power at the Preamp
> -22 dBm
mixer power level (dBm)= input power (dBm)-attenuation (dB)
Displayed Average Noise Level (DANL)*4
Preamp off
0 dB attenuation; RF Input is terminated with a 50 Ohm load. RBW 10 Hz; VBW 10 Hz; span 500 Hz; reference level = -60dBm; trace average ≥ 40
9 kHz to 100 kHz, < -93 dBm
Nominal
100 kHz to 1 MHz, < -90 dBm - 3 x (f/100 kHz) dB
1 MHz to 10 MHz, < -122 dBm
10 MHz to 3 GHz, < -122 dBm
Preamp on
0 dB attenuation; RF Input is terminated with a 50 Ohm load. RBW 10 Hz; VBW 10Hz; span 500 Hz; reference level = -60dBm; trace average ≥ 40
100 kHz to 1 MHz, < -108 dBm - 3 x (f/100 kHz) dB
Nominal
1 MHz to 10 MHz, < -142 dBm
10 MHz to 3 GHz, < -142 dBm + 3 x (f/1 GHz) dB
[4] DANL spec shall exclude the Spurious Response
Level Display Range
Scales
Log, Linear
Units
dBm, dBmV, dBuV, V, W
Marker Level Readout
0.01 dB
Log scale
0.01 % of reference level
Linear scale
Level Display Modes
Trace, Topographic, Spectrogram
Single / split Windows
Number of Traces
4
Detector
Positive-peak, negative-peak, sample, normal, RMS(not Video)
Can be setup for each trace separately
Trace Functions
Clear & Write, Max/Min Hold, View, Blank, Average
Absolute Amplitude Accuracy
Absolute Point
Center=160 MHz ; RBW 10 kHz; VBW 1 kHz; span 100 kHz; log scale; 1 dB/div; peak detector; 20 to 30°C; signal 0 dBm
Preamp off
± 0.3 dB
Ref level 0 dBm; 10 dB RF attenuation
Preamp on
± 0.4 dB
Ref level -30 dBm; 0 dB RF attenuation
Frequency Response
Preamp off
Attenuation: 10 dB; Reference: 160 MHz; 20 to 30°C
100 kHz to 2.0 GHz
± 0.5 dB
2.0GHz to 3.0 GHz
± 0.7 dB
Preamp on
Attenuation: 0 dB; Reference: 160 MHz; 20 to 30°C
1 MHz to 2.0 GHz
± 0.6 dB
2.0GHz to 3.0 GHz
± 0.8 dB
Attenuation Switching Uncertainty
Attenuator setting
0 to 50 dB in 1 dB step
Uncertainty
± 0.25 dB
reference: 160 MHz, 10dB attenuation
RBW Filter Switching Uncertainty
1 Hz to 1 MHz
± 0.25 dB
reference : 10 kHz RBW
Level Measurement Uncertainty
Overall Amplitude Accuracy
± 1.5 dB
20 to 30°C; frequency > 1 MHz; Signal input 0 to -50 dBm; Reference level 0 to -50 dBm;
Input attenuation 10 dB;
RBW 1 kHz; VBW 1 kHz; after cal; Preamp Off
± 0.5 dB
Typical
Spurious Response
Second Harmonic Intercept
Preamp off; signal input -30dBm; 0 dB attenuation
+35 dBm
Typical; 10 MHz < fc < 775 MHz
+60 dBm
Typical; 775 MHz ≤ fc < 1.5 GHz
Third-order Intercept
Preamp off; signal input -30dBm; 0 dB attenuation
> 1dBm
300 MHz to 3 GHz
Input Related Spurious
< -60 dBc
Input signal level -30 dBm, Att. mode, Att=0 dB; 20-30 degree C
Residual Response (inherent)
<-90 dBm
Input terminated; 0 dB attenuation; Preamp off
Sweep
Sweep Time
Range
22ms to 1000s
Span >= 100 Hz
50us to 1000s
Span = 0 Hz; Min Resolution = 10 us
Sweep Mode
Continuous; Single
Trigger Source
Free run; Video; External
Trigger Slope
Positive or negative edge
RF Preamplifier
Frequency Range
1 MHz to 3 GHz
Gain
18 dB
Nominal
(installed as standard)
Front Panel Input/Output
RF Input
Connector Type
N-type female
Impedance
50 ohm, nominal
VSWR
<1.6 :1
300 kHz to 3 GHz; Input attenuator ≥ 10 dB
Power for Option
Connector Type
SMB male
Voltage/Current
DC +7V / 500 mA max
With short-circuit protection
USB Host
Connector Type
A plug
Protocol
Version 2.0
Supports Full/High/Low speed
MicroSD Socket
Protocol
SD 1.1
Supported Cards
MicroSD, MicroSDHC
Up to 32GB capacity
Rear Panel Input/Output
Reference Output
Connector Type
BNC female
Output Frequency
10 MHz
Output Amplitude
3.3V CMOS
Output Impedance
50 ohm
Reference Input
Connector Type
BNC female
Input Reference Frequency
10 MHz
Input Amplitude
-5 dBm to +10 dBm
Frequency Lock Range
Within ± 5 ppm of the input reference frequency
Alarm Output
Connector Type
BNC female; Open-collector
Trigger Input/ Gated Sweep Input
Connector Type
BNC female
Input Amplitude
3.3V CMOS
Switch
Auto selection by function
LAN TCP/IP Interface
Connector Type
RJ-45
Base
10Base-T; 100Base-Tx; Auto-MDIX
USB Device
Connector Type
B plug
For remote control only; supports USB TMC
Protocol
Version 2.0
Supports Full/High speed
IF Output
Connector Type
SMA female
Impedance
50 ohm
Nominal
IF Frequency
886 MHz
Nominal
Output level
-25 dBm
10 dB attenuation; RF input: 0 dBm @ 1 GHz;
Earphone Output
Connector Type
DVI-I ( integrated analog and digital) , Single Link
Compatible with VGA or HDMI standard through adapter
RS232 Interface
Connector Type
D-sub 9-pin female
Tx,Rx,RTS,CTS
GPIB Interface (Optional)
Connector Type
IEEE-488 bus connector
AC Power Input
Power Source
AC 100 V to 240 V, 50 / 60 Hz
Auto range selection
Battery Pack (Optional)
Battery pack
6 cells, Li-Ion rechargeable, 3S2P
With UN38.3 Certification
Voltage
DC 10.8 V
Capacity
5200 mAh / 56Wh
General
Internal Data storage
16 MB nominal
Power Consumption
<65 W
Warm-up Time
< 30 minutes
Temperature Range
+5 °C to +45 °C
Operating
-20 °C to + 70 °C
Storage
Weight
4.5 kg (9.9 lb)
Inc. all options (Basic+TG+GPIB+Battery)
Dimensions
210 x 350 x 100 (mm)
Approximately
8.3 x 13.8 x 3.9 (in)
Tracking Generator*5 (Optional)
Frequency Range
100 kHz to 3 GHz
Output Power
-50 dBm to 0 dBm in 0.5 dB steps
Absolute Accuracy
± 0.5 dB
@160 MHz, -10 dBm, Source attenuation 10 dB, 20 to 30°C
Output Flatness
Referenced to 160 MHz, -10 dBm
100 kHz to 2 GHz
± 1.5 dB
2 GHz to 3 GHz
± 2.0 dB
Output Level Switching Uncertainty
± 0.8 dB
Referenced to -10 dBm
Harmonics
< -30 dBc
Typical, output level = -10 dBm
Reverse Power
+30 dBm max.
Connector type
N-type female
Impedance
50 ohm
Nominal
Output VSWR
< 1.6:1
300 kHz to 3 GHz, source attenuation ≥ 12 dB
[5] The minimum RBW filter is 10 kHz when the TG output is ON.
USB Power Sensor (Optional)
Type
Average power sensor
Model: PWS-06
Interface to Meter
USB cable to GSP930 Front-Panel USB Host
Connector Type
N-type male, 50 ohm nominal
Input VSWR
1.1: 1
Typical
1.3: 1
Max
Input Frequency
1 to 6200 MHz
Sensing Level
-32 to +20 dBm
Max. Input Damage Power
<= 27 dBm
Power Measurement Uncertainty
@ 25 °C
-30 dBm to +5 dBm:
1 MHz to 3GHz: ±0.10 dB typical
±0.30 dB max.
3 GHz to 6 GHz: ±0.15 dB typical
±0.30 dB max.
+5 dBm to +12 dBm:
1 MHz to 3GHz: ±0.15 dB typical
±0.30 dB max.
3 GHz to 6 GHz: ±0.15 dB typical
±0.30 dB max.
+12 dBm to +20 dBm:
1 MHz to 3GHz: ±0.20 dB typical
±0.40 dB max.
3 GHz to 6 GHz: ±0.20 dB typical
±0.40 dB max.
Power Measurement Uncertainty
@ 0 to 25 °C
-30 dBm to +5 dBm:
1 MHz to 3GHz: ±0.25 dB typical
3 GHz to 6 GHz: ±0.25 dB typical
+5 dBm to +12 dBm:
1 MHz to 3GHz: ±0.20 dB typical
3 GHz to 6 GHz: ±0.20 dB typical
+12 dBm to +20 dBm:
1 MHz to 3GHz: ±0.35 dB typical
3 GHz to 6 GHz: ±0.30 dB typical
Linearity @ 25 °C
±3 %
Measurement Speed
100 ms for Low Noise Mode
Typical
30 ms for Fast Mode
-
Frequency Range: 9kHz ~ 3GHz
-
High Frequency Stability: 0.025ppm
-
3dB RBW: 1Hz ~ 1MHz
-
6dB EMI Filter: 200Hz, 9kHz, 120kHz, 1MHz
-
Phase Noise: -88dBc/Hz @1GHz, 10kHz Offset
-
Built-in Measurement Functions: 2FSK Analysis, AM/FM/ASK/FSK Demodulation & Analysis, EMC Pre-test, P1dB point, Harmonic, Channel Power, N-dB bandwidth, OCBW, ACPR, SEM, TOI, CNR, CTB, CSO, Noise Marker, Frequency Counter, Time Domain Power, Gated Sweep
-
Built-in Spectrogram and Topographic Display Modes
-
886MHz IF Output for User’s Extended Applications
-
Remote Control Interface: LAN, USB, RS-232, GPIB (Optional)
-
Built-in Preamplifier, 50dB Attenuator, and Sequence Function
-
Optional 6GHz Power Sensor, Tracking Generator, Battery Back
RBW/Span >=0.02 ;
Mkr level to DNL>30 dB
≥10 dB
Input attenuation 10 dB;
RBW 1 kHz; VBW 1 kHz; after cal; Preamp Off
(installed as standard)
@ 25 °C
@ 0 to 25 °C
ANDALAN PRIMA SEJAHTERA
Kami CV ANDALAN PRIMA SEJAHTERA.
Alamat
Jl. Muchtar Tabrani, Bintang Metropol Blok A-7 No. 16 , Bekasi Utara
Phone : 021 - 29253187, 29253184, Fax : 021-29253186
Email : support@andalanprimasejahtera.com / maria@andalanprimasejahtera.com
Website : www.andalanprimasejahtera.com
Yang berdiri sejak tahun 2005 adalah distributor laboratory equipment, reagent, measuring and test instrument
Perusahaan kami mengageni beberapa produk yaitu, peralatan untuk oil dan gas, lingkungan , Electrical, Kimia dan air
Perlu kami sampaikan pula bahwa kami mempunyai tenaga yang profesional dalam menangani pemasangan dan perbaikan alat/barang untuk keperluan laboratorium dan menjamin After Sales Service bagi barang atau peralatan yang kami supplay.
Free Member
Jl. Muchtar Tabrani Perum. Bintang Metropol Blok A7 no 16
Jawa Barat - Bekasi
Login Terakhir 12-02-2019
02129253184
081290773137
Produk Lainnya
